RUBBERSEAL LIQUIFLEX®-PRO is a high performance, wet-on-wet, cold applied liquid waterproofing system that is fully reinforced with a polyester fabric. It has significant advantages over conventional liquid roofing systems because it can be applied wet-on-wet, is a single liquid product, fume free and virtually odourless.
LIQUIFLEX®-PRO has many advantages over traditional types of waterproofing particularly within the refurbishment sector. As well as being cold applied, LIQUIFLEX®-PRO offers a seamless roof finish. It forms a permanently elastic, seamless membrane and is ideal for long term waterproofing of awkward roof details such as pipe penetrations, upstands and gutters. These characteristics also make the system a perfect choice for the long term protection of balconies, terraces and patios.
LIQUIFLEX®-PRO will bond to most substrates, allowing its use in many situations without having to remove and dispose of the existing roof covering. This saves time and avoids the cost of removal and environmental issues associated with disposal.
Installers prefer LIQUIFLEX®-PRO because it is extremely convenient. It is a single liquid product keeping waste at a minimum. The benefits of wet on wet mean no need to hang around waiting for it to dry or come back to site several times. With no fumes, it is also safer and more pleasant to work with.
LIQUIFLEX®-PRO is our main product in the LIQUIFLEX® range. Did you know that we also have accompanying items to go along with it?
Listed below are the other items in the LIQUIFLEX® family that not only help to extend the warranty of the base system, but can also improve the visual aesthetics of the system.
LIQUIFLEX®-PRO is used to waterproof the area by applying two wet matted coats with Liquiflex matting sandwiched in-between.
Mix the LIQUIFLEX®-PRO at a low speed in the tin before use. Apply to the roof using a solvent resistant roller
Total coverage rate of 2kg per square metre.
LIQUIFLEX®-PRO will be shower-proof in 30 – 40 minutes and can take foot traffic after 4 – 6 hours. Membrane is fully cured in 24 hours.
LIQUIFLEX®-PRO can also be used with Liquiflex® Accelerator if a quicker drying time is required for trafficked areas.
|Specific gravity (kg/m³)||1.320 ~ 1.420||DIN 53 217|
|Viscosity at 23ºC||2.650 cps||ASTM D2196-86|
|Dry extract||>90||EN 1768|
|Flash Point (ºC)||42ºC||ASTM D93|
|Ashes at 450ºC % weight||42 ~ 47%||EN 1879|
|Temperature||2ºC and rising and not exceeding 30ºC|
|Hardness Shore A at 23ºC||C > 75|
|Tensile strength||6 MPa|
|Dry time||2-8 hours. Fully cured 24 hours|
Liquiprime is a single component, low viscosity primer. It has been specifically designed to increase bonding and improve the surface levelling of some substrates prior to the application of the Liquiflex®-Pro.
Liquiprime can be applied with roller or brush straight out of the tin at a coverage rate of 150-200ml per m2.
Tin size is 5Ltr (Therefore minimum coverage of 25m2 can be achieved).
Liquiprime is translucent with excellent bonding onto porous surfaces.
If the surface to be treated is uneven in places, areas can be built up by using a coat of Liquiprime mixed with silica sand to level it, prior to applying a full coat of the primer.
Tack time: 60 mins (20C) – Wait until completely dry before applying Liquiflex-Pro.
Liquiprime must be used on all concrete substrates, TPO single ply and any rubber outlets.
The use of Liquitop is recommended to increase UV stability, for trafficable areas or achieve extended guarantees.
INSTRUCTIONS & COVERAGE
Liquitop is a single component top coat applied at a coverage rate of 150g/m2 per sqm in one layer to cover around 5sqm per litre.
Liquitop has a drying time of 2 hours once applied.
Liquitop must be applied no later than 48 hours after Liquiflex was applied and on a clean and dry surface.
For carparks and high traffic areas Liquitop HT should be used.
Liquiflex® Clear is a single component, aliphatic–UV resistant transparent coating that can be used for waterproofing of roof lights, lead, copper or in general to protect the aesthetic look of any roof. Liquiflex® Clear is also recommended to encapsulate mineral slate in anti-skid finishes, providing a tough, sealed, trafficable surface.
Liquiflex® Clear has a pot life of two hours and drying time of 1-2 hours based on weather conditions.
Liquiflex® Clear can also be used as a temporary waterproofing / primer for OSB or plywood decks when used in conjunction with Liquiflex® matting.
Liquithix can be added to Liquiflex-Pro membrane to thicken the liquid when going onto vertical surface areas.
Thickening the liquid can help to avoid runs and drops, or sagging of the re-inforcing matt.
Liquithix can be mixed to Liquiflex-Pro at ratio of 100ml – 500ml per 15kg tin, depending on requirements.
Liquithix should not be confused with an accelerator as it does not affect the membrane curing time or process.
Liquiflex® Matting is used embedded between two coats of Liquiflex®-Pro.
LIQUIFLEX® MATTING – 100MM (100mm wide x 120mts long)
Designed to be used in joints, splits and reinforcing small areas
LIQUIFLEX® MATTING – 200MM (200mm wide x 120mts long)
Designed to be used in upstands, gutters and wrapping outlets, corners, etc.
LIQUIFLEX® MATTING – 1MT
Designed to be used on main roof
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.